Blast Cabinet Maintenance FB

Blast Cabinet Maintenance Explained

The less you pay for a sandblasting cabinet the more blast cabinet maintenance it will require, and the more parts will wear out.  This is because normally the more you pay for a machine the larger the dust collector and the better the machine parts are permitting higher daily usage with larger and faster gun and nozzle sizes.

Factors that Affect Blast Cabinet Maintenance:

  1. Abrasive type used, cutting or non-cutting
  2. Abrasive hardness on the Moe Scale (mineral hardness scale)
  3. Abrasive mesh size used, larger to small
  4. Gun or nozzle size to determine cfm used (cubic feet per minute of compressed air)
  5. Highest blasting pressure used not the lowest
  6. Daily machine use
  7. Condition of part surface with respect to material being removed from the part
  8. Part hardness
  9. Type of delivery, siphon or direct pressure

This short list of changing variables affecting blast cabinet maintenance is by no means comprehensive, additional factors can impact regular maintenance. One important thing to remember is each machine’s maintenance is based on operation and application, so the same two models will have different maintenance schedules if they’re doing different things. This is true even if they’re used in the same shop and being run by the same people.

ProTip: One of the most common mistakes people make is thinking blasting machines only need maintenance when a part wears out! We mention this because oftentimes a blasting machine is considered a piece of equipment that simply runs and runs. The truth is these machines need regularly scheduled maintenance targeting both preventive tune-ups and daily machine wear.

Blast Cabinet Maintenance List

Most blast cabinet maintenance is located in the dust collector, and we cover dust collector maintenance in this blog post. The remaining maintenance is primarily regular visual inspection and replacement of various parts on the machine before they start impacting your bottom line. A few things you should be sure to check regularly are:

Nozzles

These should be replaced when they appear worn, you start to lose impact velocity with siphon delivery models, or find that you need massive air amounts with direct pressure models. It’s smart to check your nozzles daily, or before you use the cabinet, to make sure you’re getting optimal performance and always keep a drill bit handy to check the bore size.

Abrasive hoses

Normal wear creates holes in any abrasive hose, so checking these monthly is a good idea. It’s a red flag if you find yourself turning up your air pressure to maintain cleaning speed. You may be losing abrasive through a hole in your abrasive hose.

Mixing valves

Your blasting cabinet should come with a manual that explains how to properly maintain the machine’s mixing valves. If it doesn’t, you should contact the manufacturer for guidance. Media Blast cabinet manuals are available for customers online.

Work Grates

Replace any visually worn out parts like the machine work grates using daily inspection.

Air inlet filters

Just like any air filter, you need to regularly replace the air inlet filters on your blast cabinet. Neglecting this task reduces the airflow into the cabinet or possibly allows abrasive to escape the cabinet.

View windows

If your machine doesn’t come with a window protector then it’s crucial that you regularly inspect and replace your window. Most cabinet operators compensate for poor visibility by bringing the part they are processing closer and closer to the view window. Unfortunately, at close range the abrasive bouncing back can destroy the window in 10 minutes.

Separator

At some time, depending on abrasive size and type used, the separator will wear out and require replacement. Not replacing it will allow abrasive to flow into the dust collector, which increases operating cost, quickly loads the dust collector, and reduces blower airflow and cabinet visibility.

Debris Removal

Just like the lint trap in your drier, you have to clean the abrasive scalper screen. This collects all debris inside the unit including gaskets, silicone and large particles of blasted items.  Unlike the dryer that simply stops drying efficiently, a dirty abrasive scalper screen will eventually prevent abrasive from flowing back into the mixing valve and to the gun.

Drain & Purge Machine

If a machine is used daily we advise that the unit be drained and purged monthly to eliminate nesting around the mixing valve that flows abrasive to the nozzle or gun. If you use your cabinet less frequently, you can adjust your maintenance schedule accordingly. Just be aware that material removed from cleaning parts means material is mixed into the abrasive.

Airjet and Gun Body

All siphon abrasive delivery machines need to have the airjet and gun body inspected. This is required more frequently for cutting abrasive applications and larger gun sizes.

ProTip: Even with the most meticulous maintenance schedule, sandblasting cabinets will eventually wear out. These machines are built to remove something from the parts you’re blasting and at some point the cabinet will start to remove itself. When that will happen is hard to say, but the features and quality of the unit can greatly impact its lifecycle.

To Sum It Up:

Blasting machines can be very simple but they do require some regular maintenance and part replacement. The right blast cabinet maintenance schedule for your machine depends on how frequently the machine is being used, its application, and what construction you have, e.g. (light duty, R&D non-production or production).

Media Blast manufactures 170 different blasting cabinet modelsWet, Dry, Siphon, Gravity Feed and Direct PressureLight DutyR&D and Full Production with special blasting cabinets for Steel Shot, Plastic and Soda. We have a complete line of smaller micro units for special low frictional heat applications. We want to help you buy the right machine the first time!